[1]方昊天,李 扬. 超低温下轴拉钢混构件裂缝控制可靠度分析[J].湖北工业大学学报,2021,(1):74-78.
　FANG Haotian,LI Yang. Reliability Analysis of the Maximum Crack of Reinforced Concrete Members under Axial Tension under Ultra-low Temperature[J].,2021,(1):74-78.
点击复制

 超低温下轴拉钢混构件裂缝控制可靠度分析()
分享到：

《湖北工业大学学报》[ISSN:1003-4684/CN:42-1752/Z]

卷:
期数:
2021年第1期
页码:
74-78
栏目:
湖北工业大学学报
出版日期:
2021-02-18

文章信息/Info

Title:
 Reliability Analysis of the Maximum Crack of Reinforced Concrete Members under Axial Tension under Ultra-low Temperature
文章编号:
1003-4684(2021)01-0074-05
作者:
 方昊天;  李 扬
 湖北工业大学土木建筑与环境学院， 湖北 武汉 430068
Author(s):
 FANG Haotian;  LI Yang
 School of Civil Engin.,Architecture and Environment,Hubei Univ.of Tech.,Wuhan 430068,China
关键词:
 ; 超低温;  钢筋混凝土;  最大裂缝;  可靠度;  蒙特卡洛法
Keywords:
 ; ultra-low temperature;  reinforced concrete;  maximum crack;  reliability;  Monte Carlo method
分类号:
TU311.2
文献标志码:
A
摘要:
 基于蒙特卡洛法，由规范给出的正常使用极限状态下的功能函数，通过改变钢筋混凝土构件的温度、保护层厚度、荷载效应比、钢筋尺寸、混凝土等级，对超低温下钢筋混凝土轴拉构件最大裂缝可靠度进行分析得出：钢筋混凝土轴拉构件由常温20℃降至-160℃情况下，构件轴拉可靠指标β呈先降低后升高最后趋于平稳的趋势；对超低温条件下构件可靠指标影响由大到小依次为钢筋尺寸、混凝土等级、荷载效应比、保护层厚度；随着温度的降低，通过提高钢筋混凝土构件材料的性能，对钢筋混凝土构件裂缝控制的效果更加明显。
Abstract:
 Based on the Monte Carlo method and the function under the normal use limit state given by the specification, the reliability of the maximum cracks at the ultra-low temperature reinforced concrete axial tensile member is analyzed by changing the temperature of the reinforced concrete member, the thickness of the protective layer, the load effect ratio, and the size of the steel bar, the concrete grade. The analysis of the reliability of the maximum cracks shows that: when the reinforced concrete axial tension member is lowered from normal temperature 20℃ to -160℃, the axial reliability index β of the component decreases first, then increases, and tends to be stable; for ultra-low temperature components, the influence of the reliability index from large to small is the size of the steel bar, the concrete grade, the load effect ratio, and the thickness of the protective layer. As the temperature decreases, by improving the performance of the reinforced concrete member material, the effect of controlling the cracks of the member is more obvious.

参考文献/References:

[1] 姚继涛,宋璨.混凝土受弯构件裂缝控制的可靠度分析[J].土木工程学报,2017,50(3):28-34.
[2] 李春秋,陈肇元.荷载作用下混凝土构件裂缝控制的若干问题[J].建筑结构,2007(1):114-119.
[3] 管俊峰,赵顺波,李晓克,等.钢筋混凝土梁裂缝宽度试验与计算方法[J].中国公路学报,2011,24(5):74-81+88.
[4] 张丽波,郭将,刘晓.响应面法与蒙特卡洛法边坡可靠性评价方法对比研究[J].武汉大学学报(工学版),2016,49(5):779-786.
[5] 时旭东,居易,马驰,等. 混凝土低温受拉强度试验研究[J]. 建筑结构, 2016, 46(13): 86-89.
[6] Lahlou Dahmani, Amar Khenane, Salah Kaci. Behavior of the reinforced concrete at cryogenic temperatures[J]. Cryogenic,2007, 47(9): 517-525.
[7] Reginald B. Kogbara,Srinath R. Iyengar,Zachary C. Grasley,Eyad A. Masad,Dan G. Zollinger. A review of concrete properties at cryogenic temperatures: Towards direct LNG containment[J]. Construction and Building Materials, 2013,47: 760-770.
[8] 谢剑，李海瑞，李会杰.超低温下钢筋与混凝土粘结性能试验研究[J].冰川冻土, 2014, 36(3): 626-631.
[9] 谢剑,雷光成,魏强,等.超低温下钢筋混凝土梁受弯性能试验研究[J]. 建筑结构学报, 2014, 35(12): 65-71.
[10] 中国建筑科学研究院.GB50010-2010.混凝土结构设计规范[S].北京:中国建筑工业出版社，2010.
[11] 李扬. 混凝土结构裂缝控制的安全度设置水平研究[D].武汉：武汉大学,2013.
[12] 蔡江勇,钟鸣,王雪亮,等.高强钢筋混凝土梁裂缝控制可靠度分析[J].建筑结构,2020,50(3):85-88.

相似文献/References:

[1]熊韧,曹海印,王焱清,等.非牛顿润滑静压轴承的节流器流量方程修正[J].湖北工业大学学报,2019,34(5):6.
　XIONG Ren,CAO Haiyin,WANG Yanqing,et al.Modified restrictor flow equations of hydrostatic bearings ubricated by non-Newtonian fluids[J].,2019,34(1):6.
[2]王照远,曹 民,王 毅,等. 场景与数据双驱动的隧道图像拼接方法[J].湖北工业大学学报,2020,(4):11.
　WANG Zhaoyuan,CAO Min,WANG Yi,et al. Tunnel Image Stitching Method based on Scene and Data[J].,2020,(1):11.
[3]潘 健,梁佳成,陈凤娇,等. 单电流闭环多重PR控制的LCL型逆变器[J].湖北工业大学学报,2020,(4):16.
　PAN Jian,LIANG Jiacheng,CHEN Fengjiao,et al. Design of LCL Grid Connected Inverter based on Single Closed Loop Control and Multiple PR Controllers[J].,2020,(1):16.
[4]王晓光,赵 萌,文益雪,等. 定子闭口槽结构对永磁电机齿槽转矩影响分析[J].湖北工业大学学报,2020,(4):25.
　WANG Xiaoguang,ZHAO Meng,WEN Yixue,et al. Study on Cogging Torque and Vibration Noise of Permanent Magnet Motor with Segmental Stator and Closed-Slot[J].,2020,(1):25.
[5]宇 卫,凃玲英,陈 健. 风电场集中接入对集电线电流保护的影响[J].湖北工业大学学报,2020,(4):29.
　YU Wei,TU Lingying,CHEN Jian. Effect of the Collective Line Current Protection when Wind Farms are Centralized Accessed to the Power System[J].,2020,(1):29.
[6]廖政斌,王泽飞,祝 珊. 二惯量系统谐振在线抑制及相位补偿[J].湖北工业大学学报,2020,(4):34.
　LIAO Zhengbin,WANG Zefei,ZHU Shan. Online Resonance Suppression and Phase Compensation for Double Inertia System[J].,2020,(1):34.
[7]王 欣,游 颖,姜天翔,等. 面向3D打印过程的产品工艺设计和优化[J].湖北工业大学学报,2020,(4):39.
　WANG Xin,YOU Ying,JIANG Tianxiang,et al. Product Process Design and Optimization for 3D Printing Processes[J].,2020,(1):39.
[8]冉晶晶,文 红,罗雅梅,等. 全自动样品前处理平台及其控制系统[J].湖北工业大学学报,2020,(4):43.
　RAN Jingjing,WEN Hong,LUO Yamei,et al. Research on Automatic Sample Preprocessing Platform and its Control System[J].,2020,(1):43.
[9]杨 磊,马志艳,石 敏,等. 基于模糊PID的小型冷库过热度控制方法[J].湖北工业大学学报,2020,(4):43.
　YANG Lei,MA Zhiyan,SHI Min,et al. Research on Superheat Control Method of Small Cold Storage based on Fuzzy PID[J].,2020,(1):43.
[10]黄 晶,周细枝,周业望. 动态注塑成型模具的设计与实验研究[J].湖北工业大学学报,2020,(4):52.
　HUANG Jing,ZHOU Xizhi,ZHOU Yewang. Design and Experimental Study of Dynamic Injection Molding[J].,2020,(1):52.
[11]严泽华,李 扬,方昊天. 超低温下钢筋混凝土梁受弯挠度可靠度分析[J].湖北工业大学学报,2022,(4):81.
　YAN Zehua,LI Yang,FANG Haotian. Reliability Analysis of Bending Deflection of Reinforced Concrete Beams under Ultra-low Temperature[J].,2022,(1):81.
[12]刘 威,李 扬. 超低温下RC短柱轴心受压承载力可靠度研究[J].湖北工业大学学报,2022,(4):92.
　LIU Wei,LI Yang. Reliability Research on Axial Compressive Bearing Capacity of RC Short Columns at Ultra-low Temperature[J].,2022,(1):92.

备注/Memo

备注/Memo:
［收稿日期］ 2020-06-03
［基金项目］ 国家自然科学基金(51508171)；湖北省自然科学基金(2020CFB860)
［第一作者］ 方昊天(1996-)， 男， 湖北武汉人，湖北工业大学硕士研究生，研究方向为结构工程
更新日期/Last Update: 2021-02-19